Description:

LSH-xW30SMD series waterproof light fixture sealed in an aluminum housing with 30 3528SMD LEDs. 30.5 cm (12 in) with 12 inch power wires on both ends. Integrated mounting magnets. 12VDC operation.

General Specifications
Beam Angle	120 degree	IP Rating	Waterproof IP67
LED Amount	30 LEDs	LED Type	3528 SMD
LEDs per Segment	30	Lifetime	30000 Hours
Suitable for Automobiles	Yes	Type	Rigid Light Bars/Aluminum Light Bars
Volts	12 VDC

LSH-xW30SMD

Built-in magnets flush mounted in grooves on rear of bars allow quick and easy attachment to ferrous materials

LSH-xW60SMD

Description:

LSH-xW60SMD series waterproof light fixture sealed in an aluminum housing with 60 3528SMD LEDs. 61 cm (24 in) with 12 inch power wires on both ends. Integrated mounting magnets. 12VDC operation.

General Specifications
Beam Angle	120 degree	IP Rating	Waterproof IP67
LED Amount	60 LEDs	LED Type	3528 SMD
LEDs per Segment	60	Lifetime	30000 Hours
Suitable for Automobiles	Yes	Type	Rigid Light Bars/Aluminum Light Bars
Volts	12 VDC

LSH-xW30SMD

Built-in magnets flush mounted in grooves on rear of bars allow quick and easy attachment to ferrous materials

LSH-xW60SMD

Product Description

Universal Red/Green/Blue (RGB) LED controller and dimmer with handheld infrared remote that can control any 12VDC RGB LED products except the RGB-2. Select from 20 static modes, custom color programming, or 6 dynamic color-changing modes with speed and ON/OFF controls. The maximum load is 3 amps per channel, 18 amps total.

LDIR-RGB3: 12VDC RGB LED Controller

The model LDIR-RGB3 is a RGB controller with handheld Infrared Remote that can be used to program custom colors, control and dim any of our Red/Green/Blue (RGB) LED Light Bars and Light Strips. Several different static colors (including pure white) and dynamic color changing modes are directly selectable and adjustable on the IR remote. Up to six different custom colors can be programmed and saved on the six DIY buttons for direct selection.

Product Specifications

Typical Wiring Schematic

NOTES:

1.) Only power with 5~24VDC power supply.
2.) Wireless controller uses one CR2025 battery.
3.) Connect according to the drawing below.
5.) QUICK and SLOW speed buttons will only work when unit is in one of the color changing (dynamic) modes.
6.) Each Controller has a handheld Remote matched to it and will only work with it's matched remote. One remote cannot operate multiple controllers.
7.) Controller can control a maximum of 48 meters of our Flexible RGB LED Strip. Over 48 meters, the strips have to connect with an amplifier to reinforce the transmission of signal. Use one RGB Amplifier for every 30 meters of additional LED Strips.
8.) Do not exceed 80% of Power Supply capacity when calculating Power Supply size to use in your system.

IR Programmable Remote Control

Description:

SMD 5050 LED Light Bar, SMD5050,30Leds, Aluminum shell LED Light Bar, 50*1.2cm, DC12V, 7.2w, IP65

The product adopts 30 pcs super bright SMD 5050 LED as luminous body.The wires come out from both ends with waterproof connector.
Available color:Red,Green,Blue,Yellow,Pure White,Warm White,RGB full color,etc.
Aluminum Alloy outer shell, sealed transparent glue Inside.
Dimension: 500*12*7mm.
Working condition:DC12V, current 0.6A, power 7.2W
Waterproof IP rank: IP65.
Widely used for advertising decoration, interior decoration, local lighting, etc.

Note:
1. Accessory: 2pcs metal U type clips, 4PCS Φ3*8 screw;

2. coming with transparent waterproof connectors on the two ends (from profile),

it is130mm long,and the strips can be connected directly, max 10pcs.

Description:

LSH-x30X3SMD series narrow rigid light bars with 3-chip 5050SMD LEDs. 22.5 inch long non-weatherproof light bars, can be cut into 1-LED segments. 12VDC operation.

Application:
1) Architectural decorative lighting
2) Path & Contour Marking
3) Auditorium walkway lighting
4) Stairway accent lighting
5) Backlighting for signage letters
6) Indoor lighting and signs

Description:

LSH-x30SMD series narrow rigid light bars with 1-chip 3528SMD LEDs. 19.5 inch long non-weatherproof light bars. Can be cut into 3-LED segments. Use C21 Interconnect and Power Jumpers. 12VDC operation.

Application:
1) Architectural decorative lighting
2) Path & Contour Marking
3) Auditorium walkway lighting
4) Stairway accent lighting
5) Backlighting for signage letters
6) Indoor lighting and signs

Description:

Product Description

Description:

Product Description

Description:

Product Description

Description:

Product Description

Description:

Product Description

Description:

Product Description

Description:

Tri-Chip SMD5050, 300Leds/reel, Flexible LED Strip, InfraRed (IR 850nm), 3-LED Cuttable, DC12V, 36W/reel, 3A/reel, 120�, 5m/reel, width : 10mm, On PCB with self-adhesive back.

This 12 volt InfraRed Flexible LED Strip are sold in one reel (16.4 feet or 5 meters) increments. If you enter a quantity of "1", you will get 16.4 feet. If you enter a quantity of "3", you will get 49.2 feet, and so on.

Our Flexible LED Strip is used for indoor and outdoor, including kitchen, boat, garden, under cabinet, and bathroom, as well as for decoration lighting, small-floodlight and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -4�F (-20�C) to more than 122�F (50�C) . This strip uses a surface-mount high power LED with wide beam angle, seamlessly and evenly bright, so it won't cast annoying shadows.

Our Flexible Led Strip heats little , which means you don't have to worry about scald or fire danger. It has a lifespan of over 50,000 hours. Like all LEDstriphome products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

1:Non-waterproof Flexible LED Strip: PCB (Printed Circuit Board) with self-adhesive back.For Indoor.
2:Waterproof Flexible LED Strip--Surface Injection: PCB surface is encapsulated with plastic Gel, with self-adhesive 3M back.(water resistant coat IP65 )For Outdoor & Indoor.
3:Waterproof Flexible LED Strip--Silicon Tube: PCB is encapsulated with silicon tube, with plastic fastener. (water resistant coat IP67)For Outdoor.
4:Waterproof Flexible LED Strip--Whole Injection: PCB both surface and back are encapsulated with plastic Gel, with plastic fastener. (water resistant coat IP68)For Outdoor.

Like all LEDstriphome products, this LED strip bears a RoHS (Restriction of Hazardous Substances) certificate that strictly ensures that no toxic materials were used in its manufacture.

Each Flexible LED strips comes equipped with an adhesive backing and can be stuck just about anywhere (except IP67/IP68 type which will come with mounting brackets).

Specification for 850nm IR Tri-Chip SMD5050 LED

Click here if you don't know how to install LED strip lights.

Description:

Tri-Chip SMD5050, 150Leds/reel, Flexible LED Strip, InfraRed (IR 850nm), 3-LED Cuttable, DC12V, 36W/reel, 3A/reel, 120�, 5m/reel, width : 10mm, On PCB with self-adhesive back.

This 12 volt InfraRed Flexible LED Strip are sold in one reel (16.4 feet or 5 meters) increments. If you enter a quantity of "1", you will get 16.4 feet. If you enter a quantity of "3", you will get 49.2 feet, and so on.

Our Flexible LED Strip is used for indoor and outdoor, including kitchen, boat, garden, under cabinet, and bathroom, as well as for decoration lighting, small-floodlight and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -4�F (-20�C) to more than 122�F (50�C) . This strip uses a surface-mount high power LED with wide beam angle, seamlessly and evenly bright, so it won't cast annoying shadows.

Our Flexible Led Strip heats little , which means you don't have to worry about scald or fire danger. It has a lifespan of over 50,000 hours. Like all LEDstriphome products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

1:Non-waterproof Flexible LED Strip: PCB (Printed Circuit Board) with self-adhesive back.For Indoor.
2:Waterproof Flexible LED Strip--Surface Injection: PCB surface is encapsulated with plastic Gel, with self-adhesive 3M back.(water resistant coat IP65 )For Outdoor & Indoor.
3:Waterproof Flexible LED Strip--Silicon Tube: PCB is encapsulated with silicon tube, with plastic fastener. (water resistant coat IP67)For Outdoor.
4:Waterproof Flexible LED Strip--Whole Injection: PCB both surface and back are encapsulated with plastic Gel, with plastic fastener. (water resistant coat IP68)For Outdoor.

Like all LEDstriphome products, this LED strip bears a RoHS (Restriction of Hazardous Substances) certificate that strictly ensures that no toxic materials were used in its manufacture.

Each Flexible LED strips comes equipped with an adhesive backing and can be stuck just about anywhere (except IP67/IP68 type which will come with mounting brackets).

Specification for 850nm IR Tri-Chip SMD5050 LED

Click here if you don't know how to install LED strip lights.

Product Description

Universal Red/Green/Blue (RGB) LED Controller & Dimmer with handheld RF Remote Color Wheel can control any 12~24VDC RGB LED products except the RGB-2. Select from several static Single Color modes or 7 dynamic color-changing modes with speed, dimming, ON/OFF controls. Maximum load is 6 amps per channel, 18 amps total.

Product Specifications

Dynamic Modes

LSH-C26E-E26: 12VDC RGB LED Controller
The Model LSH-C26E-E26 is used to control 12~24 Volt RGB LED Light Bars and Light Strips with common anode wiring, such as our LSH-RGB series Flexible Light Strips. Using the included hand held wireless Touch Color remote controller for direct accessability to all modes, RGB Light Strips can be set to one of many different static colors selectable using the touch sensitve color wheel. Also select one of 7 different dynamic color changing patterns. The remote control can also adjust pattern speed, brightness, and turn system ON and OFF. With 18 Amp continuous load capability at 12 Volts, the LSH-C26E-E26 can drive up to 48 meters of our LSH-RGB Light Strips. For longer runs use our RGB Amplifiers.

NOTES:

1.) Do not scratch the sensing area. Do not disassemble, repair, or modify the device.
2.) Disconnect the power (adapter) before installing/removing this controller.
3.) Do not use this device near water, or moisture for indoor use only.
4.) This product should only be operated from the type of power source indicated on the label.

Typical Wiring Schematic

RF Touch Color Remote Control

Music LED IR Remote Controller

Description:

Dream Color (Scan) RGB Flexible LED Strip light kit

(Scan) RGB LED Strip Kit includes the following items:

1. 1 x 12 3Amp Power supply that can supply enough current for up to 5 meters of Dream Color (Scan) RGB SMD 5050 Flexible LED strip (150LEDs). Plug Available: USA,EUROPE,UK,AUSTRALIA standard
2. 1 x 4 key LED digital Controller
3. 1 x Dream Color (Scan) RGB SMD 5050 Flexible LED strip (150LEDs)

The RF Dream Color RGB LED Strip Controller has 130x70x20mmH grayscale

On/off：It can open or close output.
Mode/Speed ：Mode adjustment / speed adjustment function switch (The first LED displays H for model adjustment, shows S for the speed adjustment.)
UP：Mode+/Speed+ button. When in mode regulator function, it is for “Mode+”. When in speed regulator function, it is for “Speed+”.
DOWN：Mode-/Speed- button. When in mode regulator function, it is for “Mode-”. When in speed regulator function, it is for “Speed-”.

Standard color changes as follows:

Dream Color RGB Flexible LED Strip

Description:

Install LED strip lights. Connecting flexible strip LEDs to power supply

General Specifications

LSH-12DCPS series enclosed power supplies. 85-264VAC input, 12VDC output. UL, TUV, and CE certified.

INTERNATIONAL AC INPUT RANGE

HIGH EFFICIENCY, LOW WORKING TEMPERATURE

SOFT-START CIRCUIT, LIMITING AC SURGE CURRENT

SHORT CIRCUIT, OVERLOAD, OVER VOLTAGE PROTECTED

COMPACT SIZE, LIGHT WEIGHT

100% FULL LOAD BURN-IN TEST

BUILT IN EMI FILTER, LOW RIPPLE NOISE

LOW COST, HIGH RELIABILITY

NOTES:

1. ALL PARAMETERS ARE SPECIFIED AT 230VAC INPUT, RATED LOAD, 25�C 70% RH AMBIENT
2. TOLERANCE: INCLUDE SET UP TOLERANCE, LINE REGULATION, LOAD REGULATION
3. RIPPLE & NOISE ARE MEASURED AT 20MHz BY USING A 12" TWISTED PAIR TERMINATED WITH A 0.1uF & 47uF CAPACITOR
4. LINE REGULATION IS MEASURED FROM LOW LINE TO HIGH LINE AT RATED LOAD
5. LOAD REGULATION IS MEASURED FROM 0% TO 100% RATED LOAD

12VDC RGB LED Controller
The Model LSH-12VRC is used to control 12 or 24 Volt RGB LED Light Bars and Light Strips with common anode wiring, such as our LSH-RGB series Light Strip. Using the included hand held wireless remote controller for direct accessability to all modes, RGB Light Strips can be set to one of 24 different static colors or one of two different dynamic color changing patterns. The remote control can also adjust pattern speed, brightness, play/pause, and turn system ON and OFF. With 12 Amp continuous load capability at 12 Volts and 18 AMP continuous load capability at 24 Volts, the LSH-12VRC can drive up to 30 meters of our LSH-RGB Light Strips. For longer runs use our RGB Amplifiers.

Product Specifications

NOTES:

1.) Do not scratch the sensing area. Do not disassemble, repair, or modify the device.
2.) Disconnect the power (adapter) before installing/removing this dimmer.
3.) Do not use this device near water, or moisture for indoor use only.
4.) This product should only be operated from the type of power source indicated on the label.
5.) Each controller has a handheld remote matched to it and will only work with it's matched remote.
6.) One remote cannot operate multiple controllers.

RF Remote Control

Typical Wiring Schematic

Description:

Weight: 0.5 oz.
Fluid Weight: 0.07 oz.

• Extra time formula allows more working time
• Dries to a super strong
• Clog-free cap

We sell Super Glue by the tube as an alternative to mounting clips and other hardware to help you install your LED fixtures. This Super Glue features a special "extra time" formula that allows more working time as you get the placement of an LED strip light or light bar just right. This glue dries to a super strong final bond.

Our Super Glue also has a clog-free cap that cleans and seals the nozzle after each use. Starting with a fresh tube of glue is made simple by a twist-on nozzle that pierces the tube, keeping your fingers clear of one incredibly strong adhesiv

Description:

We put together this 16 Foot Brighter Flexible LED Strip Light Kit as a simple, all-inclusive package that lets you set up a super bright LED light installation in minutes. The increased brightness of Brighter LED Strip Lighting make it perfect for lighting large areas or areas in need of extra light: shelf, display case, display window, and cabinet lighting; project, presentation, and exhibit lighting; workshop, garage, and basement lighting; or any interior situation. Because this easy-to-install plug-and-play LED light package features a plug-in 12V adapter, it allows for a less permanent and more portable setup. And it includes everything you need for your installation. Each kit comes with:

1.one 16.4 foot spool of Brighter Flexible Strip Light, in warm white or neutral white

2.one female DC Wire Plug, for connecting the strip's lead wires to the dimmer

3.one Inline Dimmer Switch

4.one plug-in 60 Watt Adapter

Strip lighting can fit anywhere that a light bulb can’t! In addition to being cuttable to a custom length for your project, and just a third of inch wide and less than a quarter inch high, our Brighter LED Strip is dimmable! This 12-volt, eco-friendly LED light uses only 2.2 Watts of electricity per foot, and this entire 16.4 foot strip light uses power equivalent to a single 60 Watt incandescent light bulb. Our flexible strip comes with a self-adhesive 3M backing that allows quick and easy installation on any dry, smooth surface.

You can also expand the uses of this kit by ordering any of our optional accessories, such as making anywhere from two to five separate sections out of this 16.4 foot strip with our DC Splitter Plugs (with additional Strip to DC Plug Connectors) to power both sections with one adapter.

Typical Applications

Our Flexibel LED Strip is used for indoor and outdoor, including kitchen lights,boat lights, garden lights, under cabinet lights, and bathroom lights, as well as decorative lighting, small-floodlight use and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -10� to more than 110� Fahrenheit. This strip uses a surface-mount high power LED with a wide beam angle, and is seamlessly and evenly bright, so it won't cast annoying shadows. And this multi-color waterproof LED strip lighting is fully submersible, perfect for underwater lighting.

Our Flexibe Led Strips all are little heat, which means you don't have to worry about shock or fire danger. It has a lifespan of over 50,000 hours and though it lives on a carbon diet,Like all Lighteshop products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

LEDstriphome has compiled this Flexible LED Strip Light Kit to save you both time and money. as it is estimated to last more than 50000 hours! This led strip light kit includes everything you will need to successfully install our LED Lighting.

Description:

The Waterproof Single Color LED Strip Light Kit is a package that enables you to set up an indoor or outdoor LED light installation in minutes. The wet location strip light is available in your choice of a variety of single colors, and is ideal for everyday lighting as well as holidays and special events. This kit comes with everything you'll need:

1 x 9.5-foot spool of Waterproof Flexible Strip Light, available in warm white, neutral white, red, green, blue, amber, purple, and pink

1 x 16-foot Waterproof Extension Cable

1 x female LED Light Bar Adapter Cable

1 x 12V Inline Dimmer Switch

1 x 24 Watt Plug-In Adapter

This plug-and-play waterproof LED light kit is both changeable and portable, and includes some great features:

All-inclusive, plug-and-play

All components are suitable for indoor or outdoor use and wet locations

Easy to install with included mounting clips

25% savings by buying these parts in a kit

Use this indoor and outdoor LED kit for lighting:

Decks, patios, walkways and gardens

Wet bars

Holiday decorations

Parties, and special events

Automobiles, RVs, and motorcycles

This strip light is not intended for full submersion under water and is not for use in salt water or chlorine conditions.

Technical parameters:

Input Voltage : 12V DC
Power Consumption (per spool): 14 Watts / 1.2A
Available Colors : warm white, neutral white, red, green, blue, amber, pink, purple
Color Temp.: 2700k (ww), 5000k (nw)
Lumens per ft. : 70 (ww), 78 (nw), 24 (red), 68 (green), 12 (blue), 29 (amber), 36 (pink), 0.9 (purple)
CRI: 75 (ww), 80 (nw)

Spool Weight: 9 oz.
Width: 0.3 in.
Depth: 0.25 in.
Spool Length: 9.5 ft.
IP Rating: IP68

Bulbs per ft.: 18
LED Spacing: 0.65 in. / 1.65 cm (between centers)
Cuttable: every 3 LEDs / 2 in. / 5cm
Beam Angle : 120�
Fixture Surface Temp. : 68� - 104� F / 20� - 40� C
UV/IR Radiation: None
Lifespan: 50,000 hours

Not for use in or around chlorinated or salt water.

Typical Applications

Our Flexibel LED Strip is used for indoor and outdoor, including kitchen lights,boat lights, garden lights, under cabinet lights, and bathroom lights, as well as decorative lighting, small-floodlight use and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -10� to more than 110� Fahrenheit. This strip uses a surface-mount high power LED with a wide beam angle, and is seamlessly and evenly bright, so it won't cast annoying shadows. And this multi-color waterproof LED strip lighting is fully submersible, perfect for underwater lighting.

Our Flexibe Led Strips all are little heat, which means you don't have to worry about shock or fire danger. It has a lifespan of over 50,000 hours and though it lives on a carbon diet,Like all Lighteshop products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

LEDstriphome has compiled this Flexible LED Strip Light Kit to save you both time and money. as it is estimated to last more than 50000 hours! This led strip light kit includes everything you will need to successfully install our LED Lighting.

Description:

Summarization

With LEDstriphome RF01 RGB color controller you will get a high performance solution for your color control needs, with 3 different control modes (Radio Frequency based wall mounted panel, control station and Radio Frequency Remote Control). 25 modes, including 18 color changing ones and full control of brightness and speed of change.

With this RGB color controller you will be able to control up to 32ft / 10m (2 reels) of our RGB Tri-core LED strips. You can expand the reach of the controller by using a signal amplifier.

Technical Parameters

HIGH PERFORMANCE:

Using advanced micro control unit, it allows a complete wireless control both from the Remote Control and from the Wireless Wall Control unit. Includes power-fail memory, synchronized indicator light and allows a wide array of functions.

FULL COLOR CONTROL:

Our RF01 RGB controller has 25 modes, 7 static color modes and 18 color changing ones, where you will be able to adjust not only speed but also brightness and all this available through a wireless remote control and a wireless wall unit. Full control of up to 4A per channel with the possibility of expanding the reach through the use of signal repeaters

SIMPLE INSTALLATION:

REMOTE CONTROL:

DIMENSIONS:

Description:

Size: approx 30x30mm
Used for connecting two Tri-Chip series strips,end to end with 90-270 degree between them.
Indoor, Dry location use

Description:

Size: approx 30x20mm
Used for connecting two Tri-Chip series strips,end to end with 90-180 degree between them.
Indoor, Dry location use

Description:

LSH-2CS90 flexible light strip 90 degree connector. 8mm wide solder-less inserts connects two single color LSH series flexible light strips. Price is per unit.

Description:

Size: approx 20mm
Used for connecting two Tri-Chip series strips,end to end with 90 degree between them.
Indoor, Dry location use

Description:

There is no need to solder anymore! Ledstriphome has found a solution for our LED Flexible Lights, a special solder cable that is designed and manufactured for Ledstriphome. The LED Strip Connector with DC Plug connects our LED strip lighting with their DC adapters, and features our LED strip connector at one end, and our standard coaxial connector at the other.

The LED Strip Connector:

Eliminates need to solder
Provides a permanent, secure connection
Saves Time

Using the connector couldn't be simpler. Instructions for use:

Slide Flexible LED Light into the small LED molex clamp
Using care, firmly secure the clamp with the two small brown tabs by squeezing them toward the LED strip.

INSTRUCTIONS FOR USE:

1. Pull the black clamp away from the strip using the two small black tabs and match the +/- polarity of the strip and the connector.

2. Slide LEDstriphome-Core LED strip into the connector.

3. With care, push the black tabs forward securing firmly the clamp and the strip.

4. Plug in your DC adapter

Description:

Product Description

Single Color Extension Cable

If you enter a quantity of "2", you will get 2 Meters in one piece. If you enter a quantity of "8", you will get 8 Meters in one piece, and so on. Maximal : 600 Meters
e.g. if you order 5M, and want 1x3M and 1x2M, please leave your message to "Special Instructions or Order Comments" when check out, otherwise we will ship 5M in one piece.

The Extension cable may nicely be considered as an amazing accessory that provides the versatility you need in the large entire color LED installation. Regardless of whether it is best to have two spots of the large room accented with entire color LED light, but want them about identical color controller, or you desire to founded up parallel runs of Single color strip, this extension cable television set allows you create space in between color altering LED lighting bars or sections of versatile Single color lighting Strip.

You will receive an e-mail with tracking number after shipping.
The entire shopping experience is only as good as the variety and choices offered by the online store- LEDstriphome.com Non-waterproof Single Color Extension Cable . Customers buy Non-waterproof Single Color Extension Cable need not have to worry about getting poor quality products. All the products are brand new. All the orders are very promptly shipped and delivered. Moreover, each order is packed carefully to ensure that they do not undergo any damage during shipping and handling.

Mostly, orders will be arranged and shipped out within 3 working days. Shipping by UPS or DHL need 2-5 days in transportation. Shipping by flat rate need about 2-3 weeks in transportation.

Description:

LSH-2CS solder-less interconnect jumper for flexible light strips. 8mm wide insert and 4 1/2 inches long. Connects to LSH series light strips. Price is per unit.

No need to solder anymore!

INSTRUCTIONS FOR USE:

1. Pull the black clamp away from the strip using the two small black tabs and match the +/- polarity of the strip and the connector.

2. Slide Core LED strip into the connector.

3. With care, push the black tabs forward securing firmly the clamp and the strip.

4. Repeat process with the other strip piece, making sure polarities are respected.

Description:

LSH10-2CS solder-less two contact flexible light strip interconnect. 10mm wide, 4 1/2 inches long, connects two single color flexible light strips and strip segments.

No need to solder anymore!

INSTRUCTIONS FOR USE:

1. Pull the black clamp away from the strip using the two small black tabs and match the +/- polarity of the strip and the connector.

2. Slide Core LED strip into the connector.

3. With care, push the black tabs forward securing firmly the clamp and the strip.

4. Repeat process with the other strip piece, making sure polarities are respected.

Description:

This LED RGB Light Strip Power Connector with DC plug.Only Use for Ultra-Flexible waterpoof Tri-Chip LED Strip lights.The other end provides sockets directly connected to the LED light strip pins.

RLB adapter cable for connecting CPS series power supplies with RLB product.

SIMPLE INSTALLATION:

Description:

Product Description

Description:

Product Description

Description:

10mm silicone end cap for use with ST10 silicone tubing and WFLS-GL sealant. Four holes for easy wiring installation.

Used for re-sealing Waterproof Strip Light that has been cut to a custom length.

Description:

10mm silicone end cap with 2 holes for wiring, to be used with silicone tubing and WFLS-GL waterproof sealant. Two holes for easy wiring installation.

Used for re-sealing Waterproof Strip Light that has been cut to a custom length.

Description:

8mm silicone end cap for use with ST8 silicone tubing and WFLS-GL waterproof sealant. Two holes for easy wiring installation.

Used for re-sealing Waterproof Strip Light that has been cut to a custom length.

Description:

8mm silicone end cap for use with ST8 silicone tubing and WFLS-GL sealant. There are no hole inserts for ending runs.

Used for re-sealing Waterproof Strip Light that has been cut to a custom length.

Description:

10mm silicone end cap for use with ST10 silicone tubing and WFLS-GL sealant. There are no hole inserts for ending runs.

Used for re-sealing Waterproof Strip Light that has been cut to a custom length.

Description:

RGB160 series Dream-Color Flexible RGB LED Strip

LSH-RGB160 series programmable chasing RGB Not-waterproof flexible LED light strip with 160 high power SMD RGB LEDs. 5 meter (16.45 ft) Not- waterproof flexible light strips. For use with Dream Color RGB LED Controller only. 5 VDC operation.

You Can Chick Here Buy This Dream Color 160 LEDs Flexible LED Strip light kit

General Specifications
Beam Pattern	100�	Color	RGB
Current Draw	2445 mA	Current Draw per Foot	149 mA
IP Rating	67	Number of LEDs on Unit	160
LED Type	5050SMD	LEDs per Segment	160
Lifetime	40000 hrs	MCD Per Foot	11658 mcd/ft
MCD Per LED	1200 mcd/led	Millicandela	192000 mcd
Type	Flexible Light Strips	Operating Voltage Range	5 V
Wattage Consumption	12.2 W	Wattage per Foot	0.8 W
Wavelength	626/525/470 nm
Dimensions: 502cm(197.64") x 1.6cm(0.63") x 0.55cm(0.22")
All specifications are subject to change without notice

Product Specifications

Applications:	Color selection, change, and chase with speed, direction and length control for accent lighting
Function:	Control LSH-RGB series Light Strips using controller unit or RF remote
Operating Voltage:	12 Volts DC (use included 12VDC 1A Compact Power Supply)
Connection Mode:	Common Anode (+)
Output:	2 SPI signals
Maximum Load Current:	-
Output Power:	-
Static Power Consumption:	2.2 Watts
Overall Size:	(L)94 X (W)58 X (H)26 mm
Control Method:	6 button on Controller Unit or wireless RF Remote Control
Batteries Required:	23A, 12V battery for Remote (included)
Modes:	83 Color chasing or changing
Operating Temperature:	-25~60�C

Typical Wiring Schematic

NOTES:

1.)VERY IMPORTANT: Supply voltage for Controller is 12 Volts DC, power with included 12VDC Power Supply, do not exceed

2.)VERY IMPORTANT: Supply voltage for SWDC-RGB series Light Strips is 5 Volts DC, 12 Volts will destroy the SWDC-RGB series LED Strip

3.) Connect according to the drawing below.
4.) + (plus) and - (minus) #IC buttons will only work when unit is off.
5.) Each Controller has a handheld Remote matched to it and will only work with it's matched remote. One remote cannot operate multiple controllers.
6.) Controller can control a maximum of 30 meters of our Flexible RGB LED Strip. Over 30 meters, the Strips have to connect with an amplifier to reinforce the transmission of signal.
7.) Do not exceed 80% of Power Supply capacity when calculating Power Supply size to use in your system.

Description:

RGB160 series Dream-Color Flexible RGB LED Strip

LSH-DCRGB160 series programmable chasing RGB waterproof flexible LED light strip with 160 high power SMD RGB LEDs. 5 meter (16.45 ft) waterproof flexible light strips. For use with Dream Color RGB LED Controller only. 5 VDC operation.

You Can Chick Here Buy This Dream Color 160 LEDs Flexible LED Strip light kit

General Specifications
Beam Pattern	100�	Color	RGB
Current Draw	2445 mA	Current Draw per Foot	149 mA
IP Rating	67	Number of LEDs on Unit	160
LED Type	5050SMD	LEDs per Segment	160
Lifetime	40000 hrs	MCD Per Foot	11658 mcd/ft
MCD Per LED	1200 mcd/led	Millicandela	192000 mcd
Type	Flexible Light Strips	Operating Voltage Range	5 V
Wattage Consumption	12.2 W	Wattage per Foot	0.8 W
Wavelength	626/525/470 nm
Dimensions: 502cm(197.64") x 1.6cm(0.63") x 0.55cm(0.22")
All specifications are subject to change without notice

Product Specifications

Applications:	Color selection, change, and chase with speed, direction and length control for accent lighting
Function:	Control LSH-RGB series Light Strips using controller unit or RF remote
Operating Voltage:	12 Volts DC (use included 12VDC 1A Compact Power Supply)
Connection Mode:	Common Anode (+)
Output:	2 SPI signals
Maximum Load Current:	-
Output Power:	-
Static Power Consumption:	2.2 Watts
Overall Size:	(L)94 X (W)58 X (H)26 mm
Control Method:	6 button on Controller Unit or wireless RF Remote Control
Batteries Required:	23A, 12V battery for Remote (included)
Modes:	83 Color chasing or changing
Operating Temperature:	-25~60�C

Typical Wiring Schematic

NOTES:

1.)VERY IMPORTANT: Supply voltage for Controller is 12 Volts DC, power with included 12VDC Power Supply, do not exceed

2.)VERY IMPORTANT: Supply voltage for SWDC-RGB series Light Strips is 5 Volts DC, 12 Volts will destroy the SWDC-RGB series LED Strip

3.) Connect according to the drawing below.
4.) + (plus) and - (minus) #IC buttons will only work when unit is off.
5.) Each Controller has a handheld Remote matched to it and will only work with it's matched remote. One remote cannot operate multiple controllers.
6.) Controller can control a maximum of 30 meters of our Flexible RGB LED Strip. Over 30 meters, the Strips have to connect with an amplifier to reinforce the transmission of signal.
7.) Do not exceed 80% of Power Supply capacity when calculating Power Supply size to use in your system.

Description:

Our Flexible LED Strip is used for indoor and outdoor, including kitchen, boat, garden, under cabinet, and bathroom, as well as for decoration lighting, small-floodlight and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -4�F (-20�C) to more than 122�F (50�C) . This strip uses a surface-mount high power LED with wide beam angle, seamlessly and evenly bright, so it won't cast annoying shadows.

Our Flexible Led Strip heats little , which means you don't have to worry about scald or fire danger. It has a lifespan of over 50,000 hours. Like all LEDstriphome products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

1:Non-waterproof Flexible LED Strip: PCB (Printed Circuit Board) with self-adhesive back.For Indoor.
2:Waterproof Flexible LED Strip--Surface Injection: PCB surface is encapsulated with plastic Gel, with self-adhesive 3M back.(water resistant coat IP65 )For Outdoor & Indoor.
3:Waterproof Flexible LED Strip--Silicon Tube: PCB is encapsulated with silicon tube, with plastic fastener. (water resistant coat IP67)For Outdoor.
4:Waterproof Flexible LED Strip--Whole Injection: PCB both surface and back are encapsulated with plastic Gel, with plastic fastener. (water resistant coat IP68)For Outdoor.

Click here if you don't know how to install LED strip lights.

Description:

Our Flexible LED Strip is used for indoor and outdoor, including kitchen, boat, garden, under cabinet, and bathroom, as well as for decoration lighting, small-floodlight and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -4�F (-20�C) to more than 122�F (50�C) . This strip uses a surface-mount high power LED with wide beam angle, seamlessly and evenly bright, so it won't cast annoying shadows.

Our Flexible Led Strip heats little , which means you don't have to worry about scald or fire danger. It has a lifespan of over 50,000 hours. Like all LEDstriphome products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

1:Non-waterproof Flexible LED Strip: PCB (Printed Circuit Board) with self-adhesive back.For Indoor.
2:Waterproof Flexible LED Strip--Surface Injection: PCB surface is encapsulated with plastic Gel, with self-adhesive 3M back.(water resistant coat IP65 )For Outdoor & Indoor.
3:Waterproof Flexible LED Strip--Silicon Tube: PCB is encapsulated with silicon tube, with plastic fastener. (water resistant coat IP67)For Outdoor.
4:Waterproof Flexible LED Strip--Whole Injection: PCB both surface and back are encapsulated with plastic Gel, with plastic fastener. (water resistant coat IP68)For Outdoor.

Click here if you don't know how to install LED strip lights.

Description:

Our Flexible LED Strip is used for indoor and outdoor, including kitchen, boat, garden, under cabinet, and bathroom, as well as for decoration lighting, small-floodlight and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -4�F (-20�C) to more than 122�F (50�C) . This strip uses a surface-mount high power LED with wide beam angle, seamlessly and evenly bright, so it won't cast annoying shadows.

Our Flexible Led Strip heats little , which means you don't have to worry about scald or fire danger. It has a lifespan of over 50,000 hours. Like all LEDstriphome products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

1:Non-waterproof Flexible LED Strip: PCB (Printed Circuit Board) with self-adhesive back.For Indoor.
2:Waterproof Flexible LED Strip--Surface Injection: PCB surface is encapsulated with plastic Gel, with self-adhesive 3M back.(water resistant coat IP65 )For Outdoor & Indoor.
3:Waterproof Flexible LED Strip--Silicon Tube: PCB is encapsulated with silicon tube, with plastic fastener. (water resistant coat IP67)For Outdoor.
4:Waterproof Flexible LED Strip--Whole Injection: PCB both surface and back are encapsulated with plastic Gel, with plastic fastener. (water resistant coat IP68)For Outdoor.

Click here if you don't know how to install LED strip lights.

Description:

Our Flexible LED Strip is used for indoor and outdoor, including kitchen, boat, garden, under cabinet, and bathroom, as well as for decoration lighting, small-floodlight and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -4�F (-20�C) to more than 122�F (50�C) . This strip uses a surface-mount high power LED with wide beam angle, seamlessly and evenly bright, so it won't cast annoying shadows.

Our Flexible Led Strip heats little , which means you don't have to worry about scald or fire danger. It has a lifespan of over 50,000 hours. Like all LEDstriphome products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

1:Non-waterproof Flexible LED Strip: PCB (Printed Circuit Board) with self-adhesive back.For Indoor.
2:Waterproof Flexible LED Strip--Surface Injection: PCB surface is encapsulated with plastic Gel, with self-adhesive 3M back.(water resistant coat IP65 )For Outdoor & Indoor.
3:Waterproof Flexible LED Strip--Silicon Tube: PCB is encapsulated with silicon tube, with plastic fastener. (water resistant coat IP67)For Outdoor.
4:Waterproof Flexible LED Strip--Whole Injection: PCB both surface and back are encapsulated with plastic Gel, with plastic fastener. (water resistant coat IP68)For Outdoor.

Click here if you don't know how to install LED strip lights.

Description:

Our Flexible LED Strip is used for indoor and outdoor, including kitchen, boat, garden, under cabinet, and bathroom, as well as for decoration lighting, small-floodlight and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -4�F (-20�C) to more than 122�F (50�C) . This strip uses a surface-mount high power LED with wide beam angle, seamlessly and evenly bright, so it won't cast annoying shadows.

Our Flexible Led Strip heats little , which means you don't have to worry about scald or fire danger. It has a lifespan of over 50,000 hours. Like all LEDstriphome products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

1:Non-waterproof Flexible LED Strip: PCB (Printed Circuit Board) with self-adhesive back.For Indoor.
2:Waterproof Flexible LED Strip--Surface Injection: PCB surface is encapsulated with plastic Gel, with self-adhesive 3M back.(water resistant coat IP65 )For Outdoor & Indoor.
3:Waterproof Flexible LED Strip--Silicon Tube: PCB is encapsulated with silicon tube, with plastic fastener. (water resistant coat IP67)For Outdoor.
4:Waterproof Flexible LED Strip--Whole Injection: PCB both surface and back are encapsulated with plastic Gel, with plastic fastener. (water resistant coat IP68)For Outdoor.

Click here if you don't know how to install LED strip lights.

Description:

Our Flexible LED Strip is used for indoor and outdoor, including kitchen, boat, garden, under cabinet, and bathroom, as well as for decoration lighting, small-floodlight and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -4�F (-20�C) to more than 122�F (50�C) . This strip uses a surface-mount high power LED with wide beam angle, seamlessly and evenly bright, so it won't cast annoying shadows.

Our Flexible Led Strip heats little , which means you don't have to worry about scald or fire danger. It has a lifespan of over 50,000 hours. Like all LEDstriphome products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

1:Non-waterproof Flexible LED Strip: PCB (Printed Circuit Board) with self-adhesive back.For Indoor.
2:Waterproof Flexible LED Strip--Surface Injection: PCB surface is encapsulated with plastic Gel, with self-adhesive 3M back.(water resistant coat IP65 )For Outdoor & Indoor.
3:Waterproof Flexible LED Strip--Silicon Tube: PCB is encapsulated with silicon tube, with plastic fastener. (water resistant coat IP67)For Outdoor.
4:Waterproof Flexible LED Strip--Whole Injection: PCB both surface and back are encapsulated with plastic Gel, with plastic fastener. (water resistant coat IP68)For Outdoor.

Click here if you don't know how to install LED strip lights.

Description:

SMD 5050 Color Changing Brighter LED Strip

if you choose this RGB SMD 5050 Color Changing Brighter Flexible LED Strip, then you need a RGB controller ,which will give you a wide array of creative lighting options for any situation. Whether blue, red or green light, this multi-color strip light will deliver consistent, fantastic results.

Our Flexible LED Strip is used for indoor and outdoor, including kitchen, boat, garden, under cabinet, and bathroom, as well as for decoration lighting, small-floodlight and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -4�F (-20�C) to more than 122�F (50�C) . This strip uses a surface-mount high power LED with wide beam angle, seamlessly and evenly bright, so it won't cast annoying shadows.

Our Flexible Led Strip heats little , which means you don't have to worry about scald or fire danger. It has a lifespan of over 50,000 hours. Like all LEDstriphome products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

1:Non-waterproof Flexible LED Strip: PCB (Printed Circuit Board) with self-adhesive back.For Indoor.
2:Waterproof Flexible LED Strip--Surface Injection: PCB surface is encapsulated with plastic Gel, with self-adhesive 3M back.(water resistant coat IP65 )For Outdoor & Indoor.
3:Waterproof Flexible LED Strip--Silicon Tube: PCB is encapsulated with silicon tube, with plastic fastener. (water resistant coat IP67)For Outdoor.
4:Waterproof Flexible LED Strip--Whole Injection: PCB both surface and back are encapsulated with plastic Gel, with plastic fastener. (water resistant coat IP68)For Outdoor.

Click here if you don't know how to install LED strip lights.

If you want buy this LED Strip Light Kit, please click here!

Description:

SMD 5050 Color Changing Brighter LED Strip

if you choose this RGB SMD 5050 Color Changing Brighter Flexible LED Strip, then you need a RGB controller ,which will give you a wide array of creative lighting options for any situation. Whether blue, red or green light, this multi-color strip light will deliver consistent, fantastic results.

Our Flexible LED Strip is used for indoor and outdoor, including kitchen, boat, garden, under cabinet, and bathroom, as well as for decoration lighting, small-floodlight and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -4�F (-20�C) to more than 122�F (50�C) . This strip uses a surface-mount high power LED with wide beam angle, seamlessly and evenly bright, so it won't cast annoying shadows.

Our Flexible Led Strip heats little , which means you don't have to worry about scald or fire danger. It has a lifespan of over 50,000 hours. Like all LEDstriphome products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

1:Non-waterproof Flexible LED Strip: PCB (Printed Circuit Board) with self-adhesive back.For Indoor.
2:Waterproof Flexible LED Strip--Surface Injection: PCB surface is encapsulated with plastic Gel, with self-adhesive 3M back.(water resistant coat IP65 )For Outdoor & Indoor.
3:Waterproof Flexible LED Strip--Silicon Tube: PCB is encapsulated with silicon tube, with plastic fastener. (water resistant coat IP67)For Outdoor.
4:Waterproof Flexible LED Strip--Whole Injection: PCB both surface and back are encapsulated with plastic Gel, with plastic fastener. (water resistant coat IP68)For Outdoor.

Click here if you don't know how to install LED strip lights.

If you want buy this LED Strip Light Kit, please click here!

Description:

SMD 5050 Color Changing Brighter LED Strip

if you choose this RGB SMD 5050 Color Changing Brighter Flexible LED Strip, then you need a RGB controller ,which will give you a wide array of creative lighting options for any situation. Whether blue, red or green light, this multi-color strip light will deliver consistent, fantastic results.

Our Flexible LED Strip is used for indoor and outdoor, including kitchen, boat, garden, under cabinet, and bathroom, as well as for decoration lighting, small-floodlight and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -4�F (-20�C) to more than 122�F (50�C) . This strip uses a surface-mount high power LED with wide beam angle, seamlessly and evenly bright, so it won't cast annoying shadows.

Our Flexible Led Strip heats little , which means you don't have to worry about scald or fire danger. It has a lifespan of over 50,000 hours. Like all LEDstriphome products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

1:Non-waterproof Flexible LED Strip: PCB (Printed Circuit Board) with self-adhesive back.For Indoor.
2:Waterproof Flexible LED Strip--Surface Injection: PCB surface is encapsulated with plastic Gel, with self-adhesive 3M back.(water resistant coat IP65 )For Outdoor & Indoor.
3:Waterproof Flexible LED Strip--Silicon Tube: PCB is encapsulated with silicon tube, with plastic fastener. (water resistant coat IP67)For Outdoor.
4:Waterproof Flexible LED Strip--Whole Injection: PCB both surface and back are encapsulated with plastic Gel, with plastic fastener. (water resistant coat IP68)For Outdoor.

Click here if you don't know how to install LED strip lights.

If you want buy this LED Strip Light Kit, please click here!

Description:

SMD 5050 Color Changing Brighter LED Strip (IP68)

if you choose this RGB SMD 5050 Color Changing Brighter Flexible LED Strip, then you need a RGB controller ,which will give you a wide array of creative lighting options for any situation. Whether blue, red or green light, this multi-color strip light will deliver consistent, fantastic results.

Description:

SMD 5050 Color Changing Brighter LED Strip (IP67)

if you choose this RGB SMD 5050 Color Changing Brighter Flexible LED Strip, then you need a RGB controller ,which will give you a wide array of creative lighting options for any situation. Whether blue, red or green light, this multi-color strip light will deliver consistent, fantastic results.

Description:

SMD 5050 Color Changing Brighter LED Strip (IP67)

if you choose this RGB SMD 5050 Color Changing Brighter Flexible LED Strip, then you need a RGB controller ,which will give you a wide array of creative lighting options for any situation. Whether blue, red or green light, this multi-color strip light will deliver consistent, fantastic results.

Description:

LSH-x1200-24V series extra long flexible LED light strip. 20 meters (65.6 feet) long with 1200 high power 1-chip 3528SMD LEDs with adhesive backing can be cut into 6-LED segments. 24 VDC Operation - 1 unit (20m) maximum run.

20m LSH-x1200-24V series Flexible Light Strips use 3528SMD LEDs with 180� viewing angle - 24 Volt DC operation - (width: 12mm x height: 2.5mm)

LSH-x1200-24V

Typical Wiring Diagram

Maximum Flexibility Precaution

Our Flexible LED Strip is used for indoor and outdoor, including kitchen, boat, garden, under cabinet, and bathroom, as well as for decoration lighting, small-floodlight and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -4�F (-20�C) to more than 122�F (50�C) . This strip uses a surface-mount high power LED with wide beam angle, seamlessly and evenly bright, so it won't cast annoying shadows.

Our Flexible Led Strip heats little , which means you don't have to worry about scald or fire danger. It has a lifespan of over 50,000 hours. Like all LEDstriphome products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

1:Non-waterproof Flexible LED Strip: PCB (Printed Circuit Board) with self-adhesive back.For Indoor.
2:Waterproof Flexible LED Strip--Surface Injection: PCB surface is encapsulated with plastic Gel, with self-adhesive 3M back.(water resistant coat IP66 )For Outdoor & Indoor.
3:Waterproof Flexible LED Strip--Silicon Tube: PCB is encapsulated with silicon tube, with plastic fastener. (water resistant coat IP67)For Outdoor.
4:Waterproof Flexible LED Strip--Whole Injection: PCB both surface and back are encapsulated with plastic Gel, with plastic fastener. (water resistant coat IP68)For Outdoor.

Click here if you don't know how to install LED strip lights.

Description:

Product Description

Description:

LSH-x480-5MM series non-weatherproof flexible LED light strip with 480 side-emitting 5mm DIP LEDs. 5 meter (16.4 ft) non-weatherproof flexible light strips with adhesive backing, can be cut into 3-LED segments (solder pads for reconnections only every 48-LED segments). 12VDC operation.

General Specifications
Beam Angle	15�	IP Rating	Non-Weatherproof
LED Amount	480	LED Type	5mm
LEDs per Segment	3	Lifetime	30000 hrs
Standards And Certifications	ROHS/FCC/CE	Suitable for Automobiles	Yes
Type	Side Emitting/Flexible Light Strips	Volts	9~14.8 V

Our Flexible LED Strip is used for indoor and outdoor, including kitchen, boat, garden, under cabinet, and bathroom, as well as for decoration lighting, small-floodlight and cove lighting. The Waterproof Flexible LED strip Light is not only impervious to water, but curves easily and performs well in temperatures ranging from -4�F (-20�C) to more than 122�F (50�C) . This strip uses a surface-mount high power LED with wide beam angle, seamlessly and evenly bright, so it won't cast annoying shadows.

Our Flexible Led Strip heats little , which means you don't have to worry about scald or fire danger. It has a lifespan of over 50,000 hours. Like all LEDstriphome products, this strip bears a RoHS certificate that strictly ensures that no toxic materials were used in its manufacture.

1:Non-waterproof Flexible LED Strip: PCB (Printed Circuit Board) with self-adhesive back.For Indoor.
2:Waterproof Flexible LED Strip--Surface Injection: PCB surface is encapsulated with plastic Gel, with self-adhesive 3M back.(water resistant coat IP65 )For Outdoor & Indoor.

Product Description

RGB-A4 series three channel RGB amplifier. Maximum 4 Amps per channel/12 Amps total. Used to increase the load capability and extend the signal of the universal RGB controllers. Required if exceeding the maximum load capability of any universal RGB controller. 12VDC operation.

Description:

12MM Strip to Strip LED connector ,Used for making connection to transformer, for connecting RGB led strip (12mm PCB) together. These are for non-waterproof 12MM wide flexible LED strip.

IINSTRUCTIONS FOR USE:

1. Pull the black clamp away from the strip using the two small black tabs and match the +/- polarity of the strip and the connector.

2. Slide Lighteshop-Core LED strip into the connector.

3. With care, push the black tabs forward securing firmly the clamp and the strip.

4. Connect the connector wires to the RGB Controller ones, making sure the polarities are respected.

Description:

Used for making connection to transformer, for connecting SMD 5050 150/300 LEDs RGB strip (10mm PCB) together. These are for non-waterproof strip only.

INSTRUCTIONS FOR USE:

1. Pull the black clamp away from the strip using the two small black tabs and match the +/- polarity of the strip and the connector.

2. Slide Lighteshop-Core LED strip into the connector.

3. With care, push the black tabs forward securing firmly the clamp and the strip.

4. Connect the connector wires to the RGB Controller ones, making sure the polarities are respected.

Description:

Product Description

RGB Extension Cable

Pay attention: If you enter a quantity of "2", you will get 2 Meters in one piece. If you enter a quantity of "8", you will get 8 Meters in one piece, and so on. Maximal : 600 Meters
e.g. if you order 5M, and want 1x3M and 1x2M, please leave your message to "Special Instructions or Order Comments" when check out, otherwise we will ship 5M in one piece.

The RGB Extension cable may nicely be considered as a amazing accessory that provides the versatility you need in the large entire color LED installation. Regardless of whether it is best to have two spots of the large room accented with entire color LED light, but want them about identical color controller, or you desire to founded up parallel runs of RGB strip, this extension cable television set allows you create space in between color altering LED lighting bars or sections of versatile RGB lighting Strip.

The entire shopping experience is only as good as the variety and choices offered by the online store- LEDstriphome.com Non-waterproof RGB Extension Cable . Customers buy Non-waterproof RGB Extension Cable need not have to worry about getting poor quality products. All the products are brand new. All the orders are very promptly shipped and delivered. Moreover, each order is packed carefully to ensure that they do not undergo any damage during shipping and handling.

Mostly, orders will be arranged and shipped out within 3 working days. Shipping by UPS or DHL need 2-5 days in transportation. Shipping by flat rate need about 2-3 weeks in transportation.
You will receive an e-mail with tracking number after shipping.

Description:

Product Description

The connections of this switch are DC coaxial, making it compatible with most of our products, whether directly, in conjunction with the Single Color LED Strip Connector with DC Plug, or by splicing to an alternate connector. The switch, whether modified or not, is perfect for all low-voltage situations. LEDStripHome customers have found this switch an essential accessory for all LED strip lighting and light bars.

Description:

Available with both Male and Female DC Plugs

The LED Adapter Splice Cable is the perfect cable for those who prefer a hard-wire connection between their LED strip lighting and their DC adapter. A substitute for the LED Light Bar Adapter Cable (which features a coaxial plug for the adapter and a two-prong plug for the light strip), the LED Adapter Splice Cable will change our standard DC plug to two exposed wires that can then be soldered directly to our LED strip lights.

The LED Adapter Splice Cable is a full 42 inches long, so it also serves the function of a safe and permanent extension cord for any of our DC adapters.

Wall Mount RGB Controller

Product Description

The Wall Mount RGB Color Controller is an advanced wireless micro-control unit used for controlling any of our full-color RGB LED lights. This package features the color controller, a lightweight wall-mounted wireless remote control, and a wireless handheld remote control, all of which allow you to change the mode, speed, and brightness of your full color LED lighting, whether LED strips, light bars, or RGB wall washers. With this wall mount unit, connection to your RGB fixtures and 12V or 24V DC power source is simple and fast. Just wire the positive and negative leads of your low voltage driver or adapter, and the three color wires and common positive wire of your color LED light to the main controller, and you’re ready to enjoy color-changing LEDs!

All of our color LED lights require a color controller to interface between the power source and the fixture, and this controller package has it all. The wireless Wall Mount RGB Controller features 21 color-changing modes, including 3 color flash, 7 color flash, fade, 2 color crossfade, and single color flashing, or you can choose one of 7 static colors. This multi-color LED controller also features a brightness control with 256 levels of brightness, and a speed control that has 100 levels. All of these features can be accessed by either of the included remotes, which also feature on/off switches.

This low heat, low voltage LED accessory is an exciting new addition to our line of energy-efficient, cutting edge LED lights, and unlocks all the possibilities in color mood, whether for a party or special event; to create mood lighting in a living room, club, bar, or restaurant; or to add dynamic color-changing to any home or business. And, like all Elemental products, this waterproof LED light holds the prestigious ROHS certificate, which ensures that no environmentally harmful components were used in manufacturing.

Technical parameters

Wiring Diagrams

DMX Wall Plate Controller

Dimensions = (Standard Double Gang) 146mm x 86mm x 25mm
Power consumption @ max 150mW
Input voltage 5V DC
Data connection RJ 45
Installation
Mounting Screws into 40mm Back box

1. Manual Solid colours select
2. Manual Pastal colours select
3. Auto colour change 5sec delay
4. Auto colour change 30sec delay
5. Auto colour change 60sec delay
6. Auto colour change 300sec delay
7. Auto colour change 600sec delay
8. Auto colour change 900sec delay
9. Auto colour change 1800sec delay
10. Auto colour change 3600sec delay
11. Auto sound to light with strobe effect
12. Auto sound to light with NO strobe effect

Wiring Diagrams

Description:

Waterproof mounting accessories for Waterproof-Whole Injection (IP68) High Power LED Flexible Light Strips. One Kit includes: 1 x Waterproof sealant tube, 5 x Silicone end caps, 10 x Mounting clips.

Description:

Used for making connection to transformer, for connecting SMD 3528 LED strips (8mm PCB) together. These are for non-waterproof strips only.

INSTRUCTIONS FOR USE:

1. Pull the black clamp away from the strip using the two small black tabs and match the +/- polarity of the strip and the connector.

2. Slide Lighteshop-Core LED strip into the connector.

3. With care, push the black tabs forward securing firmly the clamp and the strip.

4. Connect the connector wires to the Driver ones, making sure the polarities are respected.

Description:

12MM Strip to Strip LED connector,Used for connecting two RGB LED strips (12mm PCB) end to end with no space between them. These are for non-waterproof strips only.

INSTRUCTIONS FOR USE: